Devcon Ceramic Repair Putty 11700

4.9

(330)

Write Review

$ 164.99

Add to Cart

Qty

In stock

Description

Devcon Ceramic Repair Putty 11700 Devcon ceramic repair putty 11700 is a high performance, trowelable, ceramic-filled epoxy for rebuilding worn or damaged equipment Intended Use:Rebuild worn pump casings and suction plates; repair tube sheets, heat exchangers and other circulating waterequipment; restore worn chutes and hoppers; repair and rebuild butterfly and gate valves.Product features: Excellent chemical resistance Resists corrosion, erosion and cavitation Non-sagging, creamy putty chemical resistance coating Repair coating Chemical coating Surface Preparation:Thoroughly clean the surface with Devcon® Cleaner Blend 300 to remove all oil, grease and dirt.Grit blast surface area with 8-40 mesh grit, or grind with a coarse wheel or abrasive disc pad, to create increasedsurface area for better adhesion (Caution: An abrasive disc pad can only be used provided white metal is revealed).The desired profile is 3-5mil, including defined edges (do not "feather-edge” epoxy)Note: For metals exposed
Devcon Ceramic Repair Putty 11700 Devcon ceramic repair putty 11700 is a high performance, trowelable, ceramic-filled epoxy for rebuilding worn or damaged equipment Intended Use:Rebuild worn pump casings and suction plates; repair tube sheets, heat exchangers and other circulating waterequipment; restore worn chutes and hoppers; repair and rebuild butterfly and gate valves.Product features: Excellent chemical resistance Resists corrosion, erosion and cavitation Non-sagging, creamy putty chemical resistance coating Repair coating Chemical coating Surface Preparation:Thoroughly clean the surface with Devcon® Cleaner Blend 300 to remove all oil, grease and dirt.Grit blast surface area with 8-40 mesh grit, or grind with a coarse wheel or abrasive disc pad, to create increasedsurface area for better adhesion (Caution: An abrasive disc pad can only be used provided white metal is revealed).The desired profile is 3-5mil, including defined edges (do not feather-edge” epoxy)Note: For metals exposed to sea water or other salt solution, grit-blast and high-pressure-water-blast the area, then leave overnight to allow any salts in the metal to “sweat” to the surface. Repeat blasting to “sweat out” all soluble salts. Perform chloride contamination test to determine soluble salt content (should be no more than 40ppm).Clean surface again with Devcon® Cleaner Blend 300 to remove all traces of oil, grease, dust or other foreignsubstances from the grit blasting.Repair surface as soon as possible to eliminate any changes or surface contaminants working CONDITIONS: Ideal application temperature is 55°F to 90°F. In cold working conditions, directly heat repair area to 100-110°F prior to applying epoxy and maintain at this temperature during product cure to dry off any moisture, contamination or solvents, as well as to achieve maximum performance properties.Mixing Instructions:It is strongly recommended that full units be mixed, as ratios are pre-measured. Add hardener to resin Mix thoroughly with screwdriver or similar tool (continuously scrape material away from sides and bottom of container) until a uniform, streak-free consistency is obtained. INTERMEDIATE SIZES (1,2,3 lb. units): Place resin and hardener on a flat, disposable surface such as cardboard, plywood or plastic sheet. Use a trowel or wide-blade tool to mix the material as in Step 2 above.LARGE SIZES: (25 lb., 30 lb., 50 lb. buckets): Use a T-shaped mixing paddle or a propeller-type Jiffy Mixer Model ES onan electric drill. Thoroughly fold putty by vigorously moving paddle/propeller up and down until a homogenous mix of resinand hardener is attained.Application Instructions:Spread mixed material on repair area and work firmly into substrate to ensure maximum surface contact. Ceramic RepairCompound fully cures in 16 hours, at which time it can be machined, drilled, or painted. FOR BRIDGING LARGE GAPS OR HOLES :Place fiberglass sheet, expanded metal, or mechanical fasteners between repair area and Ceramic Repair Compoundprior to application. FOR VERTICAL SURFACE APPLICATIONS :Ceramic Repair Compound can be troweled up to ½” thick without sagging. Chemical immersion is possible after 24 hours FOR ± 70°F APPLICATIONS :Applying epoxy at temperatures below 70°F lengthens functional cure and pot life times. Conversely, applying above 70°Fshortens functional cure and pot life. StorageStore at room temperature, 70 °F.These are the frequently asked questions :What is chemical resistance material?Is powder coating chemical resistant?What material has the best chemical resistance?Belzona 4331 Chemical resistant coatingFeel free to contact us if there are any queries above or other questions we will be glad to assist you. Demo Practices are available too, we have our professional to guide you or recommend proper application on the products.TDSSDS Read more about Devcon products Distributor for devcon in South East AsiaDevcon Distributor for SingaporeDevcon Distributor for CambodiaDevcon Distributor for BruneiDevcon for CambodiaDevcon Distributor for MyanmarLargest Stockist fr devcon products.

Size: 3 lb Physical state/appearance: viscous liquid 25-minute working time