Sculpfun S30 Stackable Brick Feet – King Gubby

Secure your Sculpfun S30's feet to your waste board with these stackable brick feet. Just add or subtract "kids Bricks" to change height as needed. Super simple to use and compatible with the larger toy stackable bricks/blocks your kid has lying around the house. Bricks can be found here Watch the video here (the video is of the Ortur laser but shows the overall install and utility of this product as well). Are the King Gubby Stackable Brick Feet compatible with all building bricks? No, they work with DUPLO Legos or any similar sized, off-brand bricks. However, it is best to check the specifications of the bricks before purchasing to ensure compatibility. Can I use the Sculpfun S30 Brick Feet without bricks? Yes, by using the feet without any bricks, you will still have the sturdiest retaining feet on the market for your Sculpfun S30. How many bricks do I need for the Sculpfun S30 Stackable Brick Feet by King Gubby? The number of bricks required for the Stackable Brick Feet depends on the height you want to achieve. It is recommended to purchase a few extra bricks in case you need to make adjustments in the future. Each brick is 3/4 of an inch high (19mm). 19mm divided by the height of the object you are trying to get under your laser, when focused, will give you the number of bricks you need. How many bricks do I need for the King Gubby Brick Feet to use the rotary accessory?King Gubby recommends seven to eight bricks per foot or thirty two bricks total to raise your laser high enough for engraving tumblers. Keep in mind, this is a general estimate for most of the rotary accessories that we have seen, but there are different types and sizes of rotaries & tumblers on the market, and they all require different heights. Please refer to question three to get your exact measurement needs. Uses 2x4 blocks (Lego Bricks not included) These work with the large style bricks.Set of 4 feet Screw bottom plates to your table or surface, add blocks/bricks to the top until you reach the desired height. Then slide your lasers feet into the open slots on top. That's it! The holes on the outside of the feet are 4mm and the 4 inside holes are 3.8mm in diameter and the plate is 3mm high NOTE - STACKABLE BRICKS NOT INCLUDED - If you need bricks, there are HERE TIP -To increase your production rate, you can buy multiple sets of the brick bottoms to quickly exchange waste boards and have them pre-prepped.
Secure your Sculpfun S30's feet to your waste board with these stackable brick feet. Just add or subtract kids Bricks to change height as needed. Super simple to use and compatible with the larger toy stackable bricks/blocks your kid has lying around the house. Bricks can be found here Watch the video here (the video is of the Ortur laser but shows the overall install and utility of this product as well). Are the King Gubby Stackable Brick Feet compatible with all building bricks?No, they work with DUPLO Legos or any similar sized, off-brand bricks. However, it is best to check the specifications of the bricks before purchasing to ensure compatibility. Can I use the Sculpfun S30 Brick Feet without bricks?Yes, by using the feet without any bricks, you will still have the sturdiest retaining feet on the market for your Sculpfun S30. How many bricks do I need for the Sculpfun S30 Stackable Brick Feet by King Gubby?The number of bricks required for the Stackable Brick Feet depends on the height you want to achieve. It is recommended to purchase a few extra bricks in case you need to make adjustments in the future. Each brick is 3/4 of an inch high (19mm). 19mm divided by the height of the object you are trying to get under your laser, when focused, will give you the number of bricks you need. How many bricks do I need for the King Gubby Brick Feet to use the rotary accessory?King Gubby recommends seven to eight bricks per foot or thirty two bricks total to raise your laser high enough for engraving tumblers. Keep in mind, this is a general estimate for most of the rotary accessories that we have seen, but there are different types and sizes of rotaries & tumblers on the market, and they all require different heights. Please refer to question three to get your exact measurement needs. Uses 2x4 blocks (Lego Bricks not included) These work with the large style bricks.Set of 4 feet Screw bottom plates to your table or surface, add blocks/bricks to the top until you reach the desired height. Then slide your lasers feet into the open slots on top. That's it! The holes on the outside of the feet are 4mm and the 4 inside holes are 3.8mm in diameter and the plate is 3mm high NOTE - STACKABLE BRICKS NOT INCLUDED - If you need bricks, there are HERE TIP -To increase your production rate, you can buy multiple sets of the brick bottoms to quickly exchange waste boards and have them pre-prepped.

SCULPFUN S30 Laser Engraver, 5W Optical Power with

SCULPFUN S30 Ultra 33W Laser Engraving Machine

SCULPFUN S30 5W Laser Engraver Cutter with Air-assist Kit

Automatically controlled air assist system: The traditional adapter air assist will always be turned on and cannot be controlled during engraving, and

SCULPFUN S30 Automatic Air-assist Laser Engraver Machine 5W

Sculpfun S30 Stackable Brick Feet – King Gubby

SCULPFUN S30 Laser Engraver, 5W Laser Cutter

SCULPFUN Laser Rotary Roller, 360° Rotating Roller for

STL file SCULPFUN S30 Adjustable feet 🦶・3D printable model to

SCULPFUN S30 Laser Engraver with Air Assist System

Sculpfun S30 Stackable Brick Feet – King Gubby

SCULPFUN S30 Ultra 11W Laser Engraver, 0.005mm High

【Automatically Controlled Air Assist System】SCULPFUN S30 is equipped with an air assist 32-bit motherboard and a full air assist kit, including a high

SCULPFUN S30 Laser Engraver, 5W Optical Power with Automatic Full Air Assist Kit, Cut 3mm Plywood in One Pass, Replaceable Lens Design and Limit